CAD/CAM ZrO², Peek and PMMA

Prices incl. VAT
 
K-Diamonds (5 Pcs.)
K-Diamonds (5 Pcs.)
The Multilayer diamond instruments guarantee
a very long operating life on hard all-ceramic
materials. The newly developed technology of
fabrication with a special matrix-bond prevents
the breaking out of diamond particles and increases
multiple times the operating life of the instruments.
The fine grit size provides an optimal
cutting performance and high trimming capacity
during the separation with minimum vibrations.
  Application:
- Occlusal adjustment
- Adaptation of all-ceramic Abutments
- Trepanation
- Removing an all-ceramic crown
- Fitting all-ceramic restorations
from 0,00 CHF
incl. 0% tax excl. Shipping costs
TC Cutter, Plain toothing with transverse section
TC Cutter, Plain toothing with transverse section
Separation of the retention
bars. Optimum speed 20.000 rpm
TC Cutter, Plain toothing with transverse section:
0,00 CHF
incl. 0% tax excl. Shipping costs
30 Cross cut superfine
30 Cross cut superfine
For fine finishing of gold, alloys and all versions
of resins & composites – due to the special
cut also ideally suited for ceramics avoiding
occurrence of crackles.
when preparing porcelain and composite
facings. Minimum vibration when preparing
results in optimum surface quality, superior
to preparing with diamond instruments.
Controlled material reduction and increased
cost-effectiveness.
opt. 20.000 Facing composites
opt. 15.000 Low - fusing porcelain before glazing.
 
30 Cross cut superfine:
0,00 CHF
incl. 0% tax excl. Shipping costs
Exa Technique - CAD / CAM (6/100 Pcs.)
Exa Technique - CAD / CAM (6/100 Pcs.)
Smoothing of the surfaces to ensure colouring liquids
penetrate to an optimum depth. Optimum speed 10 – 15.000 rpm
Exa Technique - CAD / CAM (6/100 Pcs.):
0,00 CHF
incl. 0% tax excl. Shipping costs
C1 Round (5 Pcs.)
C1 Round (5 Pcs.)
Occlusal adjustments using tungsten carbide burs,
min. diameter 1 mm.
from 0,00 CHF
incl. 0% tax excl. Shipping costs
CeraGloss CAD/CAM
CeraGloss CAD/CAM
Smoothing surfaces using CeraGloss polishers with a
coarse grit to ensure an optimal penetration depth of
liquid colours.
CeraGloss 1 HP:
0,00 CHF
incl. 0% tax excl. Shipping costs
MultiCut
MultiCut
Universal diamond disc with a multilayered,
electroformed diamond coating on the rim
for a long service life and maximum cutting
capacity.
The MultiCut diamond disc, manufactured by
electroforming, has unique properties.
The multilayered, electroformed diamond
coating on the rim ensures a cutting performance
similar to that of a sintered diamond
disc, but with a higher degree of flexibility.
Properties
Unlike standard diamond discs, the MultiCut
universal disc features a diamond-coated
rim completely impregnated with natural diamonds.
Special bonding ensures optimum cutting.
• Multilayered diamond coating for grinding
edges and large areas
• High removal and cutting capacity
• Prepare without striations
• Flexible, highly stable disc
• Long service life
MultiCut:
0,00 CHF
incl. 0% tax excl. Shipping costs
CeraPro 1 CAD/CAM
CeraPro 1 CAD/CAM
Trimming the sprue contact points
Abrasive trimmer with ceramic bond and specifically designed
diamond grit size. Ideal for trimming of the sprue contact points
without heat-build in the all ceramic material structure.
CeraPro HP:
0,00 CHF
incl. 0% tax excl. Shipping costs
CeraPro 2 CAD/CAM
CeraPro 2 CAD/CAM
Precontouring
Abrasive trimmer with ceramic bond and
specifically designed diamond grit size.
CeraPro HP:
0,00 CHF
incl. 0% tax excl. Shipping costs
StarGloss HP CAD/CAM
StarGloss HP CAD/CAM
Polishing
After trimming and occlusal adjustments the
surface is polished, which is essential to protect
the opposing dentition.
Prepolishing
Step 1: Pink= Medium grit
For smoothing the surfaces and preparation
for final polishing.
High-shine polishing
Step 2: Grey= Superfine grit
For high-shine polishing without additional
final glaze.
StarGloss HP:
0,00 CHF
incl. 0% tax excl. Shipping costs
Diamond-Cone cutter, round end 356 FGXL (3 Pcs.)
Diamond-Cone cutter, round end 356 FGXL (3 Pcs.)
Preparing all-porcelain primary
units (implant prosthetics)
Diamond rotary instruments for preparing
all-porcelain primary units in telescope work,
telescope-borne implantology and all-porcelain
abutments.
For use in a milling unit with an air turbine
and water coolant.
Caution: Always use water coolant and
minimum pressure when preparing.
Diamond-Cone cutter, round end 356 FGXL (3 Pcs.):
0,00 CHF
incl. 0% tax excl. Shipping costs
Diamond-Parallel cutter, round end 364 FGXL (3 Pcs.)
Diamond-Parallel cutter, round end 364 FGXL (3 Pcs.)
Preparing all-porcelain primary
units (implant prosthetics)
Diamond rotary instruments for preparing
all-porcelain primary units in telescope work,
telescope-borne implantology and all-porcelain
abutments.
For use in a milling unit with an air turbine
and water coolant.
Caution: Always use water coolant and
minimum pressure when preparing.
Diamond-Parallel cutter, round end 364 FGXL (3 Pcs.):
0,00 CHF
incl. 0% tax excl. Shipping costs
Cross Cut, transverse section, VZ65
Cross Cut, transverse section, VZ65
Tungsten carbide cutter (VZ65) for trimming PEEK and PMMA materials
Specially developed tungsten carbide cutters for finishing and reworking PMMA restorations. With a new blade geometry (VZ65) for gentle
trimming of thermoplastic PMMA materials, which have the characteristic of smearing quickly. The new type of blade enables quick material
removal with a sharp cut without heating the material, does not snag and produces smooth material surfaces, allowing them to be easily polished.
Applications: For separating retention bars (0165.023HP), trimming the attachment areas of the retention bars and for adjustment of uneven
areas in the shape.
Optimum speed 20.000 rpm, only apply light pressure during preparation.
Cross Cut, transverse section, VZ65:
0,00 CHF
incl. 0% tax excl. Shipping costs
ExaStar PMMA
ExaStar PMMA
Step 1 = Brown
Medium grit
For smoothing the
surfaces and preparation
for final glaze.
Step 2 = Yellobrown
Superfine grit
For high-shine polishing
without polishing paste.
ExaStar PMMA:
0,00 CHF
incl. 0% tax excl. Shipping costs
327 CAD/CAM ZrO2 Restoration
327 CAD/CAM ZrO2 Restoration
Diamond disc for separating crowns and
bridges from HiP ZrO2 framework.
327 CAD/CAM ZrO2 Restoration:
0,00 CHF
incl. 0% tax excl. Shipping costs
1 to 15 (from a total of 15)